Screen Print & Inkjet BLAZER-PROTJB-1650 Uživatelský manuál Strana 172
- Strana / 200
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
T-Jet Blazer Series User’s Manual
Version 5.0 Revised September, 2008
156
Binding Solution for the PRO:
Adjusting the Lead Screw Bracket
The Lead Screw Bracket (or front Drive Screw Mount) should be
vertical, not at an angle.
If the Lead Screw Bracket is only slightly angled, gently tap it to
1.
straighten. Doing this can eliminate binding issues. If this did not
help the level of the Lead Screw Bracket, continue on with step 2.
In the event that the block is severely angled, remove the 3 hex
2.
screws that secure it in place.
Pull the Drive Screw downward to facilitate removing the block. Put
3.
the block back on the drive, checking for true verticality.
Reattach the block using the 3 hex screws, but only tighten to “nger
4.
tight.”
Move the Print Assembly forward until it sits about 5” from the Limit Switch. This will ensure the
5.
Drive Screw is level and in the correct position.
Tighten the 3 screws and send the printer back to
6. Home position. Set the passes to 2 or more and
press the 2 Green buttons on the User Interface.
Make sure the printer goes forward and back without binding.
7.
If you have questions, or your problem persists after completing these instructions, please call
Technical Support at 888-698-5387 or send an e-mail to [email protected]. Remember to
include your serial number and repair record(s) when emailing or have them ready when calling.
Error Code: 10004
The Encoder Strip is not being read properly.
Solution 1: Clean the Encoder Strip. Refer to Chapter 13 - Daily, Weekly and Montly Maintenance.
Prevention 1: Follow Daily Maintenance Routines
Solution 2: Make sure the Encoder Strip is seated properly in the sensor. The sensor is located in the
center of the Encoder Strip. If it’s crooked or is not securely in place, GENTLY position it back into place.
Prevention 2: Be extra careful of the Encoder Strip when performing any maintenance routines.
Lead Screw
Bracket
Drive
Screw
- User’s Manual 1
- Copyright Notices 3
- A Letter from the 5
- Developer 5
- Table of Contents 7
- - Table of Contents 11
- Basic Safety 15
- Instructions 15
- Caution: 16
- Introduction 17
- The Basics 18
- Important Support Information 19
- About the Garment Decorating 20
- Our Advice 21
- Unpacking and Setup of 23
- Your Printer 23
- Blazer PRO SETUP 25
- Ground Support 26
- Locking Nut 26
- Placement of the Shirt Boards 27
- Final Unpacking Instructions 28
- The Bulk Ink System 29
- Ink Care 31
- Changing Ink Brands 31
- NON-GENUINE EPSON CARTRIDGE 32
- Interacting with the 33
- Blazer Express 33
- Main Power Switch 34
- Powering Off 35
- Blazer PRO 37
- Powering On 39
- Printer Driver 41
- Installation 41
- Technology 44
- Learning the LCD and 45
- User Interface Controls 45
- The LCD Display Icons 46
- User Interface Touch Screens 47
- BLAZER EXPRESS 49
- BLAZER PRO: 49
- BLAZER EXPRESS: 49
- Initialization Utilities 51
- MODE SELECT 52
- POSITION 53
- Shirt Board Height Settings 56
- BLAZER PRO 56
- FOR. REV 60
- (PRINT BED) 60
- Power Cleaning Utility 61
- PAPER OUT 62
- Nozzle Check Utility 63
- Head Cleaning Utility 64
- Print Head Alignment Utility 65
- BLAZER EXPRESS Setup 66
- IMPORTANT NOTE: If you 68
- BLAZER PRO - LFP Remote Panel 71
- BLAZER PRO Setup 72
- Quick Alignment (Optional) 81
- IMPORTANT NOTE: 83
- Software Overview 85
- FastARTIST and FastRIP 86
- Image Types 87
- Photoshop 88
- A Quick Note about Photoshop 89
- Check File Mode 89
- Check File Saturation 91
- Sharpening Images 91
- Using the Tone Curve 92
- Bitmap Editing in FastARTIST 93
- Selecting Areas 93
- Channels and Layers 93
- Using the Extract Filter 95
- FastARTIST 96
- Printing Basics 99
- WARNING 100
- Basic Printing Steps: 101
- IMPORTANT POINT 102
- Chapter 10 - Printing Basics 105
- WARNING: 106
- Printing Tips and Tricks 108
- Saving a Spooled Print File 109
- Canceling a Print Job 111
- LCD Display in Print Status 113
- “Paper Out/Roll Cut” 113
- Humidity Concerns 116
- Slight Discoloration 116
- Advanced Printing 117
- With White Ink 117
- IMPORTANT POINT: 119
- Types of Pretreatment 120
- File Setup 122
- Set Print Modes 122
- Washing Directions 124
- Maintenance 124
- Printing Other Items 127
- Adjusting the Platen Height 128
- Non-Textile Printing 129
- T-Jet Non-Textile Primer 130
- Printing on Golf Balls 133
- Information 134
- Non-Textile Printing Tips 135
- Daily, Weekly and Monthly 137
- 3. Clean the Wiper Blade 139
- 5. Clean the Print Head Area 139
- 7. Ink Levels and Care 140
- WASTE TANK FULL 141
- Monthly Maintenance 143
- DO NOT LUBRICATE DRIVE SCREW 144
- Tips and Utilities to 147
- Maximize Print Quality 147
- RAM and Your Computer 148
- No Windex on Clear Cover 148
- 1 to 3 Day Downtime 149
- 4 to 9 Day Downtime 149
- 9 Days or More Downtime 149
- Additional Utilities 150
- Print Head Replacement 152
- BEFORE AFTER 153
- Chapter 15 - Troubleshooting 155
- ► Clean the Capping Station 156
- 18. Wrong Print Location 165
- LCD Error Warnings and Codes 167
- Error Code: 10000 168
- Error Code: 10001 169
- Lead Screw 172
- Error Code: 1001D 173
- Error: TOP COVER OPEN 175
- Error: RELOAD PAPER 175
- 24 Hour Emergency Support 178
- Support on the Web 178
- Chapter 16 - Product Support 179
- Webcam Video Support 180
- Support 180
- Third Party Software Support 180
- Re-crating the Blazer EXPRESS 182
- Re-crating the Blazer PRO 184
- Step 4: Attach Upper Bracers 185
- Operational Guide 189
- The Customer must: 190
- Room Preparation 191
- Room Conditions 192
- Electrical Requirements 192
- Printer Specifications 193
- Miscellaneous Information 194
- Staging Area 195
- Uncrating 195
- Requirements and Notices 197
- Declaration of Conformity 198
- Limited Warranty 199
Související produkty a manuály pro Tisk a skenování Screen Print & Inkjet BLAZER-PROTJB-1650
(60 stránky)Siemens EF 732 Series Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Kochfelder Siemens EF 732 Series.
Wir stellen 1 PDF-Handbücher Siemens EF 732 Series zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce